- X1MTM allows you to lock your X1 Mini into position from one side of the frame to the other (lock) before rotating it into the final cradle to secure it into the frame (load), "locked and loaded".
- Body made from high strength glass reinforced polymer.
- Meets the bike frame via a rubber frame protector, with rubber strips under the clips for grip and paintwork protection.
- Two frame mount clips allow progressive tightening.
- Tools needed: a 5mm Allen key.
- Maintenance: periodically check the Allen screws.
LITELOK X1 MINI
Lost your key, or need a spare?
Order a genuine Spare Keys for LITELOK Go, One, Core & X1 (£20.00), or register your existing keys so a replacement can be matched later if you ever lose them.
Fitting the X1 MINI Tactical Mount (Tactical Mount for LITELOK X1 MINI)
How do I lubricate and maintain my lock's cylinder and shackle?
If your key feels stiff or won't turn smoothly, or the shackle feels sticky and hard to open, your lock likely just needs lubricating rather than replacing. Below are the correct lubricants to use, along with the accompanying guide recommended by our engineers. This procedure only needs to be carried out if you notice that the movements are no longer as smooth as they used to be.
My key won't turn, or feels stiff or stuck
This is almost always a lubrication issue, not a fault with the key or the lock. Follow the cylinder maintenance steps below before assuming you need a replacement key or lock.
Cylinder Maintenance
Use a graphite powder lubricant to keep the cylinder working smoothly.
- Apply a small amount of the graphite powder onto the key.
- Insert the key into the lock and turn it 3-5 times to distribute the lubricant.
- Remove the key and wipe off any excess powder.
Shackle Ends & Deadbolt Mechanism
Use a silicone oil (e.g. Lubrisolve).
Shackle ends: apply a small amount of lubricant to where the shackle legs meet the lock body, as these points often collect dirt and moisture. Ensure the lubricant is evenly spread.
Deadbolt:
- Set the lock to the locked position so that the deadbolt is extended.
- Apply the lubricant to the top and bottom of the deadbolt, following the product's lubrication instructions.
- Cycle the lock 8-10 times to work the lubricant into the mechanism.
- Repeat this process 2-3 times for best results.
X1 MINI Tactical Mount (Tactical Mount for LITELOK X1 MINI)
The purpose-built frame mount for LITELOK X1 Mini, same "lock and load" two-stage cradle mechanism as the other Tactical Mounts, sized specifically for X1 Mini, Made in Britain.
X1 Key Match
A custom-manufacturing service that supplies an additional X1-range lock cut to match the key of an existing X1, X1 Mini, or X1 PLUS, a single key operates all matched locks.
X1 MINI Key Match
A custom-manufacturing service that supplies an additional LITELOK X1 MINI cut to match the key of an existing X1-range lock (X1, X1 Mini, or X1 PLUS), so a single key operates all matched locks.
X1 PLUS Key Match
A custom-manufacturing service that supplies an additional LITELOK X1 PLUS cut to match the key of an existing X1-range lock (X1, X1 Mini, or X1 PLUS), so a single key operates all matched locks.
Unfortunately, all locks can be cut with the right tools and enough time. During our own and independent tests we found that X1 MINI is at least 5 times more angle grinder resistant than the current leading D-lock as well as needing multiple discs to cut it.
Was this helpful?
Approximately 1.48kg / 3.26lbs.
Was this helpful?
There is no difference between the Bike and Moto versions of X1 MINI. They are exactly the same locks, differentiated only to show how X1 MINI can be used for both bicycles and motorcycles.
Was this helpful?
Approximately 99.5mm x 137mm.
Was this helpful?
More questions
LITELOK X1 MINI is compatible with the X1 MINI Tactical Mount for mounting on a bike frame, and is also compatible with the Restrap Holster. Both are sold separately.
Yes, tested by Sold Secure and ART. Achieves Sold Secure Powered Cycle and Bicycle Diamond levels (the highest ratings available) and ART4.
Built with Barronium®, a patented anti-angle grinder material applied as a permanently fused composite armour. The X range comprises three layers of protection: (1) fine-grain, hardened high-tensile steel core, (2) Barronium® anti-angle grinder armour fused to the core, (3) plant-based eco-rubber outer layer.
Founder and CEO Professor Neil Barron, supported by Innovate UK, working with material scientists over 5+ years.
3-year warranty covering mechanical or operational faults through normal usage; does not cover aesthetic wear and tear. Register lock and keys to enable replacement key ordering if lost.
The World's Toughest Small Lock? 🛡️ Litelok X1 Mini Launch
Launch overview introducing the compact X1 Mini.
Experiencing issues with your product?
Report a problem